Fitting a Cat Flap

Installing a cat flap might be a bit daunting however it's actually quite easy to do with the right instructions. Firstly, determine how high you want the flap to be (on average, belly height). Mark this point on your door and use the template included to guide you when drilling.
If you have a small kitten hold the door open very slightly and gradually push it to pass through. Reward the kitten each time it moves through.
Take a measurement of the door
A cat flap lets your pet to enter and exit your home at any time. This can keep your cat in good health as it ensures that it is getting enough exercise and also be able to go back inside when it is stranded in the elements during bad weather. It can also reduce the amount of time you need to spend letting it in or out and can also protect your home by letting you be aware of when it went out.
It is crucial to make sure that the cat flap is set up correctly in order to prevent your pet from being forced through it or escaping by other animals (e.g. dogs). It is important to measure your pet's belly height and the doorway to your home in order to make sure that the flap is at the correct height. If your cat is a little longer or taller than the normal, you can adjust the flap's height by moving it up or down a small amount.
Next, use a spirit-level to mark the middle of the door. This is where you will install the flap. With the markings as a reference, use the jigsaw and cut the form of the flap inside the door. After you've cut the door, sand the edges of the door to create smooth surfaces. You can then drill any fixing holes that are needed.
The process of fitting a cat flap is not as complicated as you think and it should not take more than two hours to complete the entire task from start to the end. However, the process can be a bit more difficult in the event that you have to put it into the frame of a uPVC or composite door because these doors have a wide range of thicknesses that can affect the way the holes are cut and the type of door they are inserted into. We always recommend that you call a professional if this is your first experience with glass.
Measure Your Cat
A cat flap can save you from listening to your pet meow for you to let it out or in. This is particularly helpful when your cat is inside in all weathers while you are at work.
If you are planning to install a cat flap inside your door, it is essential to determine the size of your cat prior to beginning the task. While it may seem an easy task, it is important to measure the right way or your pet will find it very difficult to use.
First, make sure that your cat is calm prior to taking measurements. You'll need to hold them in a manner that they cannot move and also ensure that the ruler or measuring tape is flat against their body, not bending in any way. You can get a precise measurement by keeping the measuring tape or the ruler flat against the body of the animal from the top to the bottom.
Once you've got your cat's measurements, it's time to examine the door to determine the best place to place the flap. Place the flap at the level of your cat's belly. This will allow them to go through the door without much effort. This will also stop the flap from making a lot of noise as it moves back and back.
You should think about the thickness of the uPVC or composite door as well. Although timber doors are of the same thickness, uPVC and composite doors may differ in their overall structure, which can make fitting a cat flap more difficult because you must ensure that the hole you cut is the correct size for your pet.
You can make use of the template included in the instructions to mark the position of the opening on the door. This will help you determine where the hole should be located and make sure that the template is set properly on the door. look at these guys is also beneficial to employ a spirit-level to ensure that the template is perfectly against the door.
Cut the Flap
You'll need to cut an opening in the door panel to install your cat flap prior to you can attach it. This can be a daunting task and it is recommended that you get a professional assist you if you don't have the knowledge or skills. You can also refer to the instructions included with the kit to learn how to do it correctly.
You can take the height of the cat's or kitten's stomach as a reference. In general, place the cat flap approximately 10-15 centimeters above the ground. This is the average height of the belly for cats. Your cat will be able to go through the flap without difficulty and it will also give the other cats or neighbours who are snooping difficult time trying to enter or leave.
Mark the position of the cat flap on the door with pencil. If your kit comes with the template you can place it on the door. Use the markings on the template to drill holes at every corner. After that, you'll be able to cut the template shape and replace it with the flap for cats.
If you are installing your cat flap on an entryway made of wood or uPVC, you are able to do it yourself if you are confident enough to use a jigsaw. Be cautious not to cut into the mullions or rails that run vertically of your door. You can use a Jigsaw to cut your panel into a square or circle according to the way you'd like to cut it. Make sure to take your time and don't force the jigsaw into cutting faster.
Once the hole is cut, carefully place your cat flap into its new home. Make sure it is securely secured. If it features caps on the screws, then place these caps onto the screws that protrude. Once the screws have been installed, sand the rough edges and seal any gaps. This will block drafts from entering your home.
Fit the Flap
If you have a simple cat flap, you can open it and encourage your pet to walk through by putting a little bit of cat food in front of the door. You can also try pushing the cat through using your hands or with a stick. Once your cat is accustomed to walking through the flap it will be able to move into and out as it wants, so you can let it out and in without having to be there to open the door to allow it in all day (and likely in all weathers).
It is possible to fit a cat flap in the UPVC doors or glass door, however it may not be as easy as installing one on a wooden external door. This is because the UPVC doors and certain types of glass doors do not have a uniform thickness. This could have a significant impact on the way you cut the flap's hole and how well the flap fits after installation.
The mounting kit could contain a template that outlines where to drill holes. If the kit doesn't include a template, you are able to make one on your own. It's important not to push the jigsaw too hard when cutting, so it doesn't make a larger than necessary hole in your door.
Most cat flaps are square or rectangular in shape but there are also some which are circular and these are generally more difficult to place. If look at these guys have a circular flap it's important to make sure the hole is in the proper position on your door, because in the event that it's not, the cat will not be able to use the flap and may be stuck out in the sun all day (or even night).
Certain cat flaps come with locks that allow you to control the time your cat is allowed to enter and leave. These can be very useful if you're concerned about your cat going out at night and coming back in because of the darkness, or if you're working all day. Certain locks can be used for entrance or exit, while others can be locked in both directions. This is helpful for older cats or sick cats who do not want to go outside in bad weather.